Virtex

This application note provides a Xilinx FPGA solution to two-dimensional filtering with a parameterized VHDL reference design.

This application note describes the implementation of six circuits necessary to perform commonly used conversions between various chroma formats.

This application note describes how to retrieve user-defined data from Xilinx configuration PROMs (XC18V00 and Platform Flash devices) after the same PROM has configured the FPGA. The method to add user-defined data to the configuration PROM file is also discussed.

Ground bounce must be controlled to ensure proper operation of high performance FPGA devices. Particular attention must be applied to minimizing board-level inductance during PCB layout. This document describes calculations that help to ensure that a design meets input undershoot and logic-low voltage requirements for devices receiving signals from an FPGA.

This application note describes the logic to perform basic word alignment and deframing specifically for SONET/SDH systems, where data is being processed at 16-bits or 64-bits per clock cycle.

This application note examines the design of scramblers for use with Synchronous Optical NETworks (SONET) and Optical Transport Network (OTN) designs using the Virtex™ series of FPGAs. The scrambler function for Synchronous Digital Hierarchy (SDH) is the same as that for SONET.

This application note describes the implementation of R’G’B’ Color Space to Y’CbCr Color Space conversion necessary in many video designs. The tick marks on red, green, blue, and Luma, assume the components are in the gamma-corrected space. No gamma correction is applied to color difference signals Cr and Cb.

This application note describes a full-featured transmitter/receiver macro that can communicate with Spartan™ and Virtex™ FPGA families via the Analog Devices ADSP-TS101S TigerSHARC™ link-port function.

The Cyclic Redundancy Check (CRC) is a powerful technique to obtain data reliability. This application note discusses the implementation of Configurable CRC Modules with LocalLink interfaces. The user can tailor the features of these modules to suit the protocol or application that is implemented in their system. The user-specified options for each of the configurable features are input parameters to the VHDL code for the modules.

MicroBlaze™ has the ability to use its dedicated FSL bus interface to integrate a customized IP core into a MicroBlaze soft processor-based system. This document describes possible methods to include customized IP cores into an SCP-based design.

This application note discusses the configuration and programming options for Xilinx Complex Programmable Logic Device (CPLD), Field Programmable Gate Array (FPGA), and PROM families and demonstrates some of the most popular configuration methods used for each family. This document includes configuration quick start guidelines for the Virtex™, Spartan™, XPLA3, XC9500, and XC18V00 families.

This application note describes techniques for remote reconfiguration of FPGAs through an Ethernet port.

One of the most significant variables that can affect the package warpage is the solder reflow process. This application note discusses the details of the solder reflow process and provides guidelines on profiling to achieve successful reflow of BGA components.

Verification is an integral part of any FPGA design project. Many older verification models are no longer appropriate to the new multimillion-gate FPGAs, and more modern methods must be brought to bear if verification is to positively affect product time to market. The methodologies used for designing and implementing a good verification plan are discussed in detail, in the context of a real-world verification case study.

This application note discusses version 2.1i of the Xilinx Design Manager (DM) and Flow Engine (FE). In 2.1i, significant enhancements for DM/FE have focused on improving ease of use. A number of new features are provided, including "self-contained revisions" and the "Smart" Flow Engine.

With the release of M2.1i, Floorplanner supports the Virtex™ family of FPGAs. This application note illustrates how the major Virtex-specific architectural features, such as BlockRAMs, global clock buffers, DLLs, and carry logic, are represented within the Floorplanner GUI and how designers can manipulate a design containing these elements.

This application note presents information on version 2.1i of the FPGA Editor and how it differs from the previous version of EPIC. (For general FPGA Editor usage, refer to the FPGA Editor Guide.) This application note also discusses how to return to EPIC type actions for zoom and pan actions.

The 2.1i software includes improvements in the Trace, Timing Analyzer, FloorPlanner, Constraints Editor, and other implementation tools to help make the designing procedure easier for Virtex™ devices. This paper is devoted to describing some of the simple steps necessary to constrain a Virtex design with the 2.1i implementation tools. The paper explains how to constrain with a CLKDLL in Virtex and examines the new look of the Timing Analyzer Reports.

This application note describes difference-based partial reconfiguration. This type of reconfiguration is used when making small changes to design parameters including logic equations, filter parameters, and I/O standards.

This package compatibility guide describes the pin-outs and established guidelines for package compatibility between the Virtex™ family and the Virtex™-E and Virtex™-E Extended Memory (Virtex™-EM) devices. For the latest information regarding the Virtex-E families, see the Xilinx Web site at http://www.xilinx.com

This application note describes how the existing dual-port block memories in the Spartan™-II and Virtex™ families can be used as Quad-Port memories. This essentially involves a data access time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the block memory in terms of bits per second will remain the same.

When designing digital systems, there is often a requirement to synchronize incoming data and clock signals with an internal system clock (i.e., the internal and external clock are at exactly the same frequency, but due to variable backplane, board, or application-specific standard product (ASSP) delays, the phase relationship is not known). The circuit described in this application note addresses this issue for both single traces and data busses up to 160 MHz in a Virtex™-E, -7 device. The speed limitation is imposed by the maximum frequency that can be accepted by the Data Locked Loop (DLL), in a mode where it is capable of providing both a new clock and a new clock shifted by 90 degrees.

Data recovery is a mechanism that allows a receiver to extract embedded clock data from an incoming data stream. The receiver usually extracts this information from the data stream concerned, but sometimes the receiver’s clock is used for data transmission. The circuit described in this application note provides a partial solution at data rates up to 160 Mb/s in a Virtex™-E -7 device, a Spartan™-IIE -6 device, or a Spartan-3 -4 device, and up to 420Mb/s in a Virtex-II -5 device or a Virtex-II Pro™ -6 device. The solution is partial in the sense that no clock is actually recovered, but the data arriving is fully extracted. The speed is limited by the maximum frequency that can be accepted by the Delay Locked Loop (DLL), in a mode where the DLL is capable of providing both a new clock, and another clock shifted by 90 degrees.

This application note describes highly optimized UART transmitter and receiver macros for Xilinx Virtex®, Virtex-E, and Spartan®-II devices. The UART_TX and UART_RX macros are fully compatible with the standard Universal Asynchronous Receiver Transmitter (UART) communication protocols used for connecting to devices, such as PCs or microcontrollers.

The convolutional interleaver technique is used in telecommunication applications such as SDH and PDH radio systems, GSM and UMTS mobile communication systems, and point-to-multipoint radio systems to protect transmission channels from noise. On the transmit side, the convolutional interleaver parallelizes serial input data into N-bit words and shifts the data word through N delay lines. The delayed data is then shifted out through a PISO shift register for transmission. At the receiver, the incoming data stream is reconstructed with dual-delay lines and shift registers.

This application note describes a high-speed, reconfigurable, full-precision Transposed Form FIR filter design implemented in the Virtex™ and Virtex™-II series and Spartan™-II family of FPGAs. The VHDL reference design provided with this application note is easily modified to change filter parameters including coefficients and the number of taps. By illustrating a design methodology for digital filters, the advantages of using FPGAs for digital signal processing applications (DSP) are emphasized. The CORE Generator™ tool provides a preoptimized alternative solution to this reference design.

Gold code generators are used extensively in Code Division Multiple Access (CDMA) systems to generate code sequences with good correlation properties. This application note describes the implementation of Gold code generators in Virtex™>, Virtex™-E, Virtex™-EM, Virtex™-II and Spartan™-II devices. The Gold code generators use efficiently-implemented Linear Feedback Shift Registers (LFSRs) in both the Virtex/Virtex-II series and Spartan-II family using the SRL16 macro.

This application note describes the use of partial reconfiguration in Virtex™ series FPGAs for the purpose of correcting Single Event Upsets to the configuration memory array induced by cosmic rays. It is essential for the reader to have a basic understanding of the Virtex SelectMAP interface as well as configuration and readback operations. An in-depth review of Xilinx Application Note XAPP138 is highly recommended.

This application note provides design advice for implementing arithmetic logic functions in two High-Level Design Languages (HDLs), VHDL and Verilog.

Code Division Multiple Access (CDMA) is a rapidly expanding data transmission technique in the emerging Universal Mobile Telecommunications System (UMTS). This application note describes the implementation of a CDMA matched filter using the architectural features of the Virtex™ series, Virtex™-II series, and Spartan™-II family of devices.

Pseudo-random Noise (PN) generators are at the heart of every spread spectrum system. Many PN generators are required within Code Division Multiple Access (CDMA) base stations. PN generators are used to implement synchronization and uniquely code individual user signals across the transmission interface. PN generators are based upon Linear Feedback Shift Registers (LFSRs). Every Look-Up-Table (LUT) in a Virtex™ series or Virtex™-II series device can be configured as a 16-bit shift register (SRL16 macro). Hence, Virtex devices implement efficient LFSRs and deliver a significant reduction in resource utilization when compared with alternative flip-flop-only PLD structures.

This application note describes the implementation of Linear Feedback Shift Registers (LFSR) using the SRL macro available in the Virtex™ and Virtex™-II series of FPGAs. The optimal implementations of a 15-bit LFSR, a 52-bit LFSR, and a 118-bit LFSR are also discussed.

Cyclic Redundancy Check (CRC) is an error-checking code widely used in data communication systems and other serial data transmission systems. CRC is based on polynomial manipulations using modulo arithmetic. Some of the common Cyclic Redundancy Check standards are CRC-8, CRC-12, CRC-16, CRC-32, and CRC-CCIT. This application note discusses the implementation of an IEEE 802.3 CRC in a Virtex™ device. The reference design provided with this application note provides Verilog point solutions for CRC-8, CRC-12, CRC-16, and CRC-32. The Perl script (crcgen.pl) used to generate this code is also included. The script generates Verilog source for CRC circuitry of any width (8, 12, 16, 32), any polynomial, and any data input width.

This application note describes an implementation of IDCT in the Virtex™ family. DCT/IDCT are used in the MPEG video standard to reduce the bandwidth requirements. IDCT is one of the most computation-intensive parts of the MPEG decoding process. A fast, hardware-based IDCT implementation is crucial to speed the MPEG decoding process. In this implementation, the inherent parallelism is exploited to achieve throughput as high as 3.28 Gbits/s, making it suitable for real-time video applications. The implementation is synthesizable Verilog code at the RTL level.

CAM (Content Addressable Memory) offers increased data search speed. In various applications based on CAM, there are differing requirements for data organization and read/write performance. The innovative design described in this application note is suited for small embedded CAMs with high-speed match and write requirements. The reference design is built using the true Dual-Port block SelectRAM™+ feature of Virtex™ FPGAs. Application Note XAPP201, "An Overview of Multiple CAM Designs in Virtex Devices," discusses the diverse solutions available when implementing CAM while introducing the specific solution described in this application note.

Content Addressable Memories (CAM) allow a fast search for specific data in a memory. Each application has different CAM requirements. A CAM design implemented in Virtex™ slices offers a flexible approach to CAM depth and width based upon LUTs configured as Shift Registers. This application note describes a fast CAM design finding a match in a single clock cycle. Application Note XAPP201, "An Overview of Multiple CAM Designs in Virtex devices," discusses the diverse solutions available when implementing CAM and introduces the specific solution described in this application note.

Content Addressable Memory (CAM) or associative memory, is a storage device, which can be addressed by its own contents. Each bit of CAM storage includes comparison logic. A data value input to the CAM is simultaneously compared with all the stored data. The match result is the corresponding address. A CAM operates as a data parallel processor. CAMs can be used to design Asynchronous Transfer Mode (ATM) switches. Implementing CAM in ATM applications is specifically described in this application note. As a reference, the application note XAPP201, “An Overview of Multiple CAM Designs in Virtex Devices,” presents diverse approaches to implement CAM in other designs.

Flexible CAMs (Content Addressable Memory) are implemented in Virtex™ devices by taking advantage of the reprogrammability of the basic LUT as a Shift Register or a SelectRAM™ memory and the fast carry logic chain. Although CAMs are also feasible in Spartan™ and XC4000X™ devices, this application note concentrates on Virtex devices.

This application note describes the design and implementation of a simple, low-cost interface to the Dallas Semiconductor’s 1-Wire devices in Virtex™ and Spartan™-II families to acquire the 64-bit ROM number. The number is available in either eight sequential byte transfers through an 8-bit data port, or a 48-bit latched parallel output. A typical application is to use the 48-bit serial number in the ROM number as the physical address of a network interface. This reference design is synthesizable and utilizes only 52 registers, 65 look-up tables (LUTs), and 55 slices of FPGA resource.

Triple Module Redundancy (TMR) combined with Single-Event Upset (SEU) correction through partial reconfiguration is a powerful and effective SEU mitigation strategy. This method is only supported for the Virtex™ series of Xilinx FPGAs. (Xilinx Application Note XAPP216 describes the use of Readback and Partial Configuration for SEU detection and correction.) This application note outlines the recommended design methodology for constructing and implementing TMR logic within the Virtex architecture.

This application note describes the transformation of multiple synchronous serial data streams to parallel data through a multi-channel serial-to-parallel converter.

Power consumption in Xilinx FPGAs depends upon the number of internal logic transitions and is proportional to the operating clock frequency. As device size increases, so does power consumption. Without an accurate thermal analysis, the heat generated could easily exceed the maximum allowable junction temperature. Power supply requirements, including initial conditions, transient behavior, turn-on, and turn-off are also important. Bypassing or decoupling the power supplies at the device, in the context of the device’s application, requires careful attention. All these aspects of the power supply must be considered to achieve successful designs.

When digital systems are used in real-world applications, it is often necessary to convert an analog voltage level to a binary number. The value of this number is directly or inversely proportional to the voltage. The analog to digital con