This Answer Record lists all known issues associated with the Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit.
Zynq UltraScale+ MPSoC Related Issues
| (Xilinx Answer 64375) | Xilinx Zynq UltraScale+ MPSoC Solution Center |
| (Xilinx Answer 65467) | Zynq UltraScale+ MPSoC - Boot and Configuration |
| (Xilinx Answer 66194) | Zynq UltraScale+ MPSoC - Processing System (PS) DDR Controller |
| (Xilinx Answer 68521) | UltraScale Boards and Kits - Failed to connect to Serial Port when using SCUI.exe |
Board / Kit Related Issues
| (Xilinx Answer 37579) | Which device do I have on my Xilinx Evaluation Kit, is it an Engineering Sample (ES) or Production silicon? |
| (Xilinx Answer 43745) | Xilinx Boards and Kits Solution Center |
| (Xilinx Answer 62629) | UltraScale Boards and Kits - Maxim Integrated Power Solution dongle |
| (Xilinx Answer 66312) | MPSoC - DDR4 configuration for the ZCU102 Board |
| (Xilinx Answer 66436) | Zynq UltraScale+ MPSoC: XSDB is not able to connect to PSU after successfully booting in SD mode on ZCU102 |
| (Xilinx Answer 66438) | Zynq UltraScale+ MPSoC: On ZCU102 QSPI24 warm booting hangs if u-boot was previously executed |
| (Xilinx Answer 66552) | Zynq UltraScale+ MPSoC: ZCU102 ENET_REST button usage |
| (Xilinx Answer 66652) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Base TRD Monitor requirements |
| (Xilinx Answer 66811) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Reprogramming the Maxim Integrated Power Controllers |
| (Xilinx Answer 66858) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - HDMI equalizer requirement for 16nm |
| (Xilinx Answer 66874) | Maxim Integrated Dongle - v2.00.1 Installer - Driver installation issue |
| (Xilinx Answer 66882) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Maxim InTune Regulator Startup Issues |
| (Xilinx Answer 67103) | UltraScale Boards and Kits - VADJ behavior and bring-up |
| (Xilinx Answer 67308) | Boards and Kits - UltraScale and UltraScale+ MPSoC Evaluation Kits - VADJ and the System Controller |
| (Xilinx Answer 67462) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - DisplayPort Monitors for use with ZCU102 GPU demo |
| (Xilinx Answer 67507) | Xilinx Boards and Kits - Power Supply Information |
| (Xilinx Answer 67565) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Can I use Bank 66 and Bank 67 on a ZCU102 board for MIPI_DPHY_DCI I/O? |
| (Xilinx Answer 67775) | 2016.2 - SDSoC - SD card instability on ZCU102 |
| (Xilinx Answer 68042) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - PCB Revision Differences |
| (Xilinx Answer 68330) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Will the ZCU102 board work as a PCIe End-Point? |
| (Xilinx Answer 68682) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - SD Card Boot Mode settings |
| (Xilinx Answer 68702) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - ZCU102 behavior when latest power supply xml files are not in use |
| (Xilinx Answer 69140) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - ARM 20-pin JTAG connector wires |
| (Xilinx Answer 69151) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Retrofitting ES2 ZCU102 with USB3.0 adapter |
| (Xilinx Answer 69164) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Jumper settings to support USB 3.0 HOST mode |
| (Xilinx Answer 69640) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Ensuring a reliable connection to System Controller GUI on ZCU102 |
| (Xilinx Answer 69745) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - PING test fails if using non-English OS |
| (Xilinx Answer 71961) | Zynq UltraScale+ MPSoC ZCU102 and ZCU106 Evaluation Kits - DDR4 SODIMM change |
Documentation Related Issues
| Answer Record | Title | Version Found | Version Resolved |
|---|---|---|---|
| (Xilinx Answer 67963) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - UG1182 (v1.0) - FMC pinout corrections | v1.0 | |
| (Xilinx Answer 68321) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - UG1182 (v1.1) - Inaccuracies in Figure 3-35 | v1.1 | |
| (Xilinx Answer 68896) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - UG1182 (v1.2) - I2C bus device addresses missing | v1.2 |
IP Related Issues
| (Xilinx Answer 65911) | HDMI Transmitter (TX) Subsystem - Release Notes and Known Issues for the Vivado 2013.1 tool and later versions |
| (Xilinx Answer 66183) | Zynq UltraScale+ MPSoC Processing System IP - Release Notes and Known Issues |
| (Xilinx Answer 66523) | 2015.4 - Zynq UltraScale+ MPSoC: FSBL for ZCU102 requires I2C interface |
| (Xilinx Answer 66592) | Zynq UltraScale+ MPSoC - SGMII using PS-GTR |
Design Tools Related Issues
| (Xilinx Answer 55776) | Release Notes and Known Issues for PetaLinux 2013.04 and later tool versions |
| (Xilinx Answer 66107) | PetaLinux 2015.4 - Product Update Release Notes and Known Issues |
| (Xilinx Answer 66553) | PetaLinux, Zynq UltraScale+ MPSoC: Ethernet link between ZCU102 and a host machine at 100M/Full does not work |
| (Xilinx Answer 66715) | 2016.1 Zynq UltraScale+ MPSoC - QSPI programming on a ZCU102 board requires the Zynq UltraScale+ device to boot in JTAG mode |
| (Xilinx Answer 67156) | PetaLinux 2016.1 - Product Update Release Notes and Known Issues |
| (Xilinx Answer 67409) | PetaLinux 2016.2 - Product Update Release Notes and Known Issues |
| (Xilinx Answer 67430) | Zynq UltraScale+ MPSoC: The 2016.2 FSBL generated using the ZCU102 SDK template is missing XPS_BOARD_ZCU102 |
| (Xilinx Answer 67480) | Zynq UltraScale+ MPSoC - Echo Server does not work on a ZCU102 board |
| (Xilinx Answer 67770) | 2016.2 SDK - GCC - Incorrect missing-braces error relating to the universal zero initializer {0} on ZCU102 boards |
| (Xilinx Answer 70132) | Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - Vivado Board File Update |
| Answer Number | Answer Title | Version Found | Version Resolved |
|---|---|---|---|
| 43750 | Xilinx Boards and Kits Solution Center - Top Issues | N/A | N/A |
| AR# 66752 | |
|---|---|
| Date | 02/20/2019 |
| Status | Active |
| Type | Known Issues |
| Boards & Kits |
|